|
MACHINE #10966 SPECIFICATIONS -MANUFACTURER: LOOPCO -TYPE: SLITTING LINE -CAPACITY -WIDTH: 60" (1524mm) -THICKNESS -MAXIMUM: .188" (4.8mm) -MINIMUM: .010" (.25mm) -CUT/SPEED CAPACITY: -55,000 PSI MATERIAL: -.062" - 5 CUTS AT 1200 FPM -.121" - 5 CUTS AT 580 FPM -.187" - 4 CUTS AT 300 FPM -.187" - 5 CUTS AT 240 FPM -.250" - 3 CUTS AT 225 FPM -89,000 PSI MATERIAL: -.062" - 5 CUTS AT 1200 FPM -.121" - 5 CUTS AT 360 FPM -.187" - 3 CUTS AT 250 FPM -119,000 PSI MATERIAL: -.062" - 4 CUTS AT 1200 FPM -.121" - 4 CUTS AT 333 FPM -.156" - 3 CUTS AT 270 FPM LINE CONSISTS OF THE FOLLOWING: -ENTRY COIL CAR: PIT MOUNTED TYPE WITH 34' TRAVEL 33" LIFT CAPACITY PUSHBUTTON CONTROL FROM OPERATOR'S STATION 10 HP SELF-CONTAINED HYDRAULIC SYSTEM ALL WHEELS ARE HYDRAULICALLY DRIVEN -UNCOILER: FOUR SEGMENT DRUM WITH HYDRAULIC EXPANSION RANGE OF 19.25"-24.50" COPPER JACKETED WATER COOLED BRAKE. REVERSING FEEDUP DRIVE WITH 3 HP MOTOR. POSITIONING BASE ON ANTI-FRICTION BEARINGS. DRIVEN HOLDDOWN ROLL. HOLDDOWN ROLL IS 36" FACE AND 8" DIAMETER. GROOVES FOR INSERTING BANDING MATERIAL. DRUM HAS FOUR WEDGES FOR EXPANSION. -ENTRY PREPARATION UNIT: TELESCOPING PEELER BLADE AT ENTRY SIDE WITH REPLACEMENT TIP AND REPLACEABLE LINERS. AUTOMATIC EDGE CONTROL WITH PHOTO-ELECTRIC EDGE SENSOR. CUSTOMER TO SUPPLY AIR TO KEEP SENSOR FREE OF DIRT AND SCALE. PRIMARY LIGHT SOURCE AND RECEIVER CONTROLS MOUNTED ON UNIT. ENTRY HYDRAULIC CROP SHEAR SLITTER ENTRY SIDE GUIDES, VERTICAL ROLL TYPE WITH REPLACEABLE BRONZE WEAR SURFACES. GUIDES ARE MANUALLY POSITIONED. HINGED TABLE BETWEEN ENTRY PREPARATION UNIT AND SLITTER. ONE PAIR OF PNEUMATICALLY ACTUATED HYDRAULICALLY DRIVEN ENTRY PINCH ROLLS. UPPER ROLL ONLY IS DRIVEN. --(1) REMOVABLE HEAD SLITTER: 7.50" DIAMETER X 63" FACE ARBORS FEEDUP DRIVE BY 75 HP 1150/2000 RPM DC MOTOR JET NUTS FOR LOCKING TOOLING ON ARBORS. DESIGNED FOR USE WITH 12.50" O.D. KNIVES AND 9.50" O.D. SPACERS. 75 HP DC DRIVE FOR HELPER DRIVE AND FREE LOOP SLITTING. -(1) SLITTER EXIT TABLE: SLIDING STEEL TABLE MOUNTED ON CAM ROLLERS. 4" DIAMETER X 64" STEEL ROLL MOUNTED ON ANTI-FRICTION BEARINGS FABRICATED STEEL SUPPORT STAND. -PIT THREADING TABLE: HYDRAULICALLY ACTUATED PIVOTING STEEL TABLE. PIVOT POINTS ARE BRONZE BUSHED WITH LUBRICATION PROVISIONS. TIVAR COVERING TO PREVENT SCRATCHING OF SLIT MATERIAL. SEPARATELY MOUNTED HYDRAULIC CYLINDER WITH ADJUSTING BRACKET, WHICH PERMITS TABLE TO BE ADJUSTED TO PROPER ELEVATION. FABRICATED STEEL SUPPORT STAND. -STRIP TENSION STAND: TENSION PADS-EASILY REMOVABLE FROM EITHER SIDE. CYLINDER OPERATED TO CONTROL LOAD ON STRANDS. QUICK OPENING FEATURE FOR EASE OF THREADING. 3.50" DIAMETER SEPARATOR SHAFT ON ANTI-FRICTION BEARINGS. ENTRY THREADING TABLE SPANS THE DISTANCE BETWEEN THE PIT THREADING TABLE SUPPORT STAND AND THE SEPARATOR SHAFT. TABLE IS HYDRAULICALLY RAISED AND LOWERED TO PROVIDE ACCESS TO SWING SEPARATOR SHAFT AND SCRAP CONVEYOR. EXIT THREAD TABLE TO GUIDE STRIPS INTO RECOILER DRUM AND OVERARM SEPARATOR. PNEUMATICALLY ACTUATED. HEAVY DUTY CLAMPING DEVICE USED TO RETAIN FREE END OF SEPARATOR SHAFT. -RECOILER: 20" DIAMETER DRUM AUTOMATIC DRUM EXPANSION AND GRIPPING OF SLIT STRANDS. DRIVEN BY 100 HP 850/2550 DC MOTOR THROUGH A TWO SPEED TYPE GEARBOX. HYDRAUICALLY OPERATED STRIPPER PLATE WITH SPRING LOADED BRONZE INSERT. SPRING SET BRAKE INTERLOCKED WITH LINE. -OVERARM SEPARATOR: MOUNTED ON TENSION STAND. MANUAL AIR VALVE CONTROLLED. COMBINATION DESIGN PERMITS OVERARM SHAFT TO BE REMOVED OR KEPT IN PLACE AND IS 3.50" IN DIAMETER. -(2) SCRAP WINDERS: HYDRAULIC DRIVE FULLY AUTOMATIC DUMP TYPE THAT EMPTIES THROUGH THE BOTTOM. CAPACITY APPROXIMATELY 1200 POUNDS AT 50 PERCENT DENSITY. MAXIMUM TRIM WIDTH 1" WIDE PER STRAND. -EXIT END FLOOR MOUNTED COIL CAR: "V" TYPE, FULL WIDTH PLATFORM TO SUPPORT SLIT STRANDS. ADJUSTABLE COIL RESTRAINING ARMS. 24" LIFT CAPACITY PUSHBUTTON CONTROL 10 HP SELF-CONTAINED HYDRAULIC SYSTEM 36' TRAVEL -ELECTRICAL DRIVE AND CONTROL PACKAGE: -(2) HYDRAULIC POWER UNITS: 20 HP, 1750 RPM AC MOTOR 20 GPM VARIABLE VOLUME, PRESSURE COMPENSATED PUMP. DESIGNED TO OPERATE AT 1500 PSI. VALVES ARE MANIFOLD MOUNTED ON THE PUMP UNITS. 60 GALLON OIL RESERVOIR. -(1) 100,000 BTU RECIRCULATING WATER COOLER: COMPLETE WITH INDUSTRIAL TYPE PUMP AND T.E.F.C. MOTOR. BLOWER AND FINNED TUBE HEAT EXCHANGER. PUSHBUTTONS AND FLOW SWITCH. 100 GALLON STAINLESS STEEL TANK. -FOUR ARM COIL TURNSTILE: SINGLE DIRECTION POWERED STRIPPER TO PUSH COILS OFF OF ARM. STORAGE SPACE FOR FOUR 40,000 LB. X 60" WIDE COILS. "C" HOOK SLOT ON ALL ARMS. HARDENED CURVED BARS ON ALL ARMS TO MINIMIZE TELESCOPING OF COILS AND WEAR. POWER ROTATION IN EITHER DIRECTION WITH LIMIT SWITCHES TO STOP ROTATION EVERY 90 DEGREES. -SCRAP CONVEYOR: STEEL HINGED BELT CONSTRUCTION WITH 6" PITCH CHAIN 36" WIDE. 24' LONG HORIZONTAL SECTION DISCHARGES INTO SCRAP PIT. SINGLE PIECE CHANNEL FRAME CONSTRUCTION FOR EASY INSTALLATION. 7.50 HP AC - T.E.F.C. DRIVE MOTOR WITH TORQUE LIMITER AND SPEED REDUCER. BELT SPEED IS 30 FPM. A CHAIN TAKE-UP IS PROVIDED AT END OF CONVEYOR. -(1) SET OF COIL STORAGE SADDLES: STORAGE SPACE FOR FIVE 40,000 LB. COILS X 62" WIDE. STEEL PLATES WITH COIL LOADING AREA COVERED WITH SPLIT TUBING TO PREVENT COIL MARKING. PLATES ARE ANCHORED TO THE PIT FOUNDATION AND ARE FLUSH WITH THE SURROUNDING FLOOR. **PRICE QUOTED IS EX-WORKS AS IS WHERE IS SUBJECT TO PRIOR SALE** **ALL SPECIFICATIONS ARE SUBJECT TO VERIFICATION BY PURCHASER**
| Machinery International Corporation | Contact Us | Email Sales Department | 203.484.0400 |