|
MACHINE 10123
SPECIFICATIONS
MANUFACTURER FENN MANUFACTURING
TYPE "5 IN 1" WIRE FLATTENING/SHAPING LINE
-TURKSHEAD AND CAPSTAN MOUNTED ON COMMON BASE
ATTACHED TO MILL
LINE CONSISTS OF THE FOLLOWING;
(1) FENN VERTICAL WIRE POWERED PAYOFF
-COIL MAX O.D. 36" (914mm)
-ARBOR DIAMETER 2 1/4"(57.15mm)
ACCEPT STANDARD WIRE CARRIER
-DRIVE MOTOR 3 HP WITH ELECTRIC BRAKE
UNIT IS EQUIPPED WITH TILT MECHANISM FOR CARRIER.
(1) FENN HORIZONTAL WIRE PAYOFF
-ARBOR SIZE 1 1/2" (38.1mm) DIAMETER TO ACCEPT STEEL DRUM
-DRUM SIZE
-FLANGE O.D. 30" (762mm)
-I.D. 14" (355.6mm)
-WIDTH 11" (279.4mm)
-ELECTRIC BRAKE ADJUSTO-BRAKE
1 1/2 HP RATING
90 VOLT
(1) FENN MODEL 2 HI ROLLING MILL
-ROLL
-DIAMETER 8 (203.2mm)
-ROLL FACE 4" (100.4mm)
-MATERIAL STEEL (ALSO SPARE SET OF CARBIDE ROLLS)
-TYPE WATER COOLED
-COLUMN SIZE 5 7/8" X 6 1/4" (150mm x 159mm)
-WINDOW OPENING 8 3/4" (222.25mm)
-BEARINGS ROLLER
-BEARING LUBE FORCED OIL
-DRIVE JOINTS 2 3/16" (55.6mm) SQUARE TYPE
-DRIVE MOTOR 75 HP 650/2000 RPM DC
FAIRBANKS MORSE, 240 VOLTS, TYPE DMZD,
FRAME 1807, NO. X82113, 1.15 SF
-DC GENERATOR 1/2 KW 2000 RPM, FAIRBANKS MORSE, 2 AMPS
250 VOLTS FULL LOAD, TYPE DGZDO, FRAME DX503
NO. X82108
-REDUCER NONE- MOTOR IS DIRECTLY COUPLED TO PINION STAND
-SCREWDOWNS MANUAL
MILL IS EQUIPPED WITH ADJUSTABLE ENTRY TABLE AND GUIDES AS WELL AS A SINGLE
PLANE 5 ROLL (1 3/8" (35mm) DIAMETER ROLLS) STRAIGHTENER AND A 2 PLANE ENTRY
GUIDE ROLL (APPROX 2 1/2" (64mm) DIAMETER ROLLS) SET UP.
(1) DOUBLE CAPSTAN
-CAPSTAN SIZE
-DIAMETER 16" (406.4mm)
-FACE WIDTH 3" (76.2mm)CONSISTING OF 4 FLAT GROOVES
EACH .625" (16mm) WIDE
CAPSTAN UNIT IS CHAIN DRIVEN FROM MILL. TENSION IS CONTROLLED VIA A WITCHITA
TUBE DISC CLUTCH.
(1) FLOOR MOUNTED DANCER
-TYPE THREE ROLL UNIT WITH TWO FIXED AND ONE MOVABLE
ROLL.
(1) 2000 LB TRAVERSING TAKE UP REEL (PROBABLY A MODEL 2312)
-CAPACITY 2,000 LBS (909 kilos)
-TYPE HYDRAULIC TRAVERSE LIMIT SWITCH CONTROLLED
REEL USES AN INTERNAL VICKERS VARIABLE DELIVERY PUMP TO CONTROL TRAVERSE
SPEED WHILE THE SHAFT IS ROTATING AND A SUPERCHARGER PUMP UNIT TO MAINTAIN
SYSTEM PRESSURE FOR MANUAL TRAVERSE WHILE SHAFT IS AT REST
-SUPERCHARGER PUMP 3/4 HP 1725 RPM
-GUIDE ROLL
-DIAMETER 6" (152.4mm)
-FACE WIDTH 2" (50.8mm)
-GROOVES 3 GROOVES
-DRIVE MOTOR 10 HP 650/2000 RPM DC, 240 VOLTS
-GEARBOX HORSEBURGH & SCOTT, SIZE RS-1000, S/N H5697
RATIO 4.56/1, INPUT RPM 1150, RATED FOR 14 HP
S/F 1.0
(2) COLLAPSIBLE DRUMS
-FLANGE DIAMETER 36" (914.4mm)
-DRUM I.D. 14" (355.6mm)
-FACE WIDTH 7 1/4" (184.15mm)
NOTE: THERE IS NO TURKS HEAD PROVIDED WITH THE LINE. CUSTOMER TO SUPPLY
N0TE: DC ELECTRICAL DRIVE NOT INCLUDED WITH LINE. CUSTOMER TO SUPPLY.
*******PRICE QUOTED IS EX-WORKS AS IS WHERE IS SUBJECT TO PRIOR SALE********
*******SPECIFICATIONS SUBJECT TO VERIFICATION BY PURCHASER*******
| Machinery International Corporation | Contact Us | Email Sales Department | 203.484.0400 |